25-44 Borough Place • Woodside, NY 11377 • 718.278.7900 • email:info@super-tek.com

Grout Stain MSDS

SECTION I – PRODUCT IDENTIFICATION

Super-Tek Products, Inc.
25-44 Borough Place, Woodside, NY 11377
Telephone #: 718-278-7900
Emergency Phone #: 718-278-7900
Generic ID: Linseed Oil Based Cement Stain; Various Colors
Product Identity: Grout Stain
Date Prepared: 1/1/02

SECTION II – INGREDIENTS & HAZARDOUS COMPONENTS

Ingredient Name	CAS Number	Percent	Exposure Limits
Petroleum Distillates	8030-30-6	60-65	500 ppm
Limestone	16389-88-1	0-5	50 mg/m3
Titanium Dioxide	13463-67-7	0-3	10mg/m3

* This product may also contain other fillers such as kaolin, talc and colored pigments which are considered "nuisance dusts". Exposures to spray mists or sanding dust should be controlled to below 2 mg/m3 through the use of a NIOSH approved dust mask respirator.

SECTION III – PHYSICAL DATA

Initial Boiling Point: 212°F.
Vapor Pressure: 2mm Hg @ 68° F.
Vapor Density (Air=1.0): 2.5.
Specific Gravity: 1.12-1.14.
Percent Volatiles: 65-70.0%.

SECTION IV – FIRE AND EXPLOSION DATA

Material is combustible. Keep away from flame. Collection of vapors can be flammable.
Use with adequate ventilation.
Flash Point: 103° F.
Explosive Limit (Product): LEL=1.1%, UEL=5.9%.
Extinguishing Media: Foam, Dry, Chemical, & Carbon Dioxide.
SPECIAL FIRE FIGHTING PROCEDURES: Use supplied-air breathing apparatus for enclosed areas. Cool exposed containers with water spray. Excessive heating may produce carbon monoxide.

SECTION V – HEALTH HAZARD DATA

EFFECTS OF EXPOSURE:
Skin: Possible mild irritation.
Eyes: Severe irritation.
Inhalation: Can cause dizziness, nausea, & vomiting.

FIRST AID:
Skin: Soap and water. Use skin cream with lanolin.
Eyes: Flush with water, lifting upper and lower lids occasionally. Consult a physician.
Inhalation: If affected, remove individual to fresh air. Use only in well ventilated areas.
Ingestion: Give plenty of water. Do not induce vomiting. Get immediate medical attention.

SECTION VI – REACTIVITY DATA

Stability: Stable.
Incompatibility: Amines, strong oxidizing agents, acids, hydroxyl and other active hydrogen compounds.
Hazardous Decomposition: Excessive heating may produce carbon monoxide.
Hazardous Polymerization: None.

SECTION VII – SPILL OR LEAK PROCEDURES

STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Remove all sources of ignition. Large spill evacuate area. Avoid breathing vapors. Wear appropriate respirator and gloves for clean-up. Dry with inert material (e.g. sand or earth) to collect material. Place in non-leaking container.

SECTION VIII – PROTECTIVE EQUIPMENT

Ventilation: Open all available windows and entrances to insure good ventilation. Provide mechanical ventilation.
Respirator Protection: Use NIOSH/MSHA Chemical Cartridge respirator required if exposure limits are exceeded.
Protective Gloves: Rubber gloves.
Eye protection: Wear glasses or protective goggles to avoid splashes.
Other Protective Equipment: None required.
WASH HANDS THOROUGHLY WITH SOAP AND WATER.

SECTION IX – SPECIAL PRECAUTIONS

Protect from freezing. Use only in applications as stated on the label. Do not take internally. Close container after each use. Avoid skin and eye contact.

Ventilation with fresh air, including open doors and windows should be observed during any flooring installation. Operate HVAC systems at 100% fresh air intake before, during and after installation to eliminate lingering odors or particulate matter.

The information accumulated herein is believed to be accurate but is not warranted to be whether originating with company or not. Recipients are advised to confirm in advance of need that the information is current, applicable and suitable to their circumstances.

KEEP OUT OF REACH OF CHILDREN. Use with adequate ventilation. Harmful if swallowed. Do not allow smoking in area where vapors may collect. Store in a cool place. Avoid prolonged exposure to vapors. Avoid contact with skin and eyes. Do not wear contact lenses.